Volume-7 (1st National Conference On Recent Innovations in Mechanical Engineering (NCRIME-2018))
- Citation
- Abstract
- Reference
- Full PDF
Paper Type | : | Research Paper |
Title | : | Urea Injection System a Nox Reducer – A Review |
Country | : | India |
Authors | : | Prof.S.M.Patil || Sourabh Patil || Shridhar Patil || Shubham Powar || Abhishek Mulik |
Abstract:Increased usage of diesel vehicles and equipments are big challenges in terms of pollution and depleting diesel fuel recourses. Significant improvements in diesel emission levels have been achieved in the last 20 years. Development of diesel engine to meet new emission regulations and adopt renewable fuels is a challenging research objective. Automobile industries worldwide are continuing efforts to control emission associated issues both on road and off road diesel vehicles with developed technology for cleaner diesel fuels, quick responding electronic control units, advanced engine design and effective after treatment of exhaust. Some of the NOx control techniques are discussed in this paper.
Keywords -Diesel engine, NOx, Urea Solution.
1) Reduction Of Nox In D.I. Diesel Engine Emission By Urea Injection K. Chithambaramasari,* N. V. Mahalakshmi** & K.
Jayachandran***
2) Nox Reduction By Using Urea Injection And Marine Ferromanganese Nodule As Scr Of A Diesel Engine Fulled With
Pongamia Pinnata Methyl Ester S.Ghosh, S.N. Chaudhuri, D. Dutta
3) Nox Reduction By Urea Under Lean Conditions Over Single Step Sol–Gel Pt/Alumina Catalyst Erol Seker , Nail Yasyerli ,
Erdogan Gulari ,∗, Christine Lambert , Robert H. Hammerle
4) Urea-SCR Catalyst System Selection for Fuel and PM Optimized Engines and a Demonstration of a Novel Urea Injection
System Ioannis Gekas, Pär Gabrielsson and Keld Johansen
5) Nox From Diesel Engine Emission And Control Strategies—A Review, Gurumoorthy S Hebbar
- Citation
- Abstract
- Reference
- Full PDF
Paper Type | : | Research Paper |
Title | : | Design And Fabrication Of Mulch Cutting Machineusing Nonconventional Source |
Country | : | India |
Authors | : | Prof. G.S Dhumal || A.P.Patwekar || S.R.Vishwakarma || C.G.Phate || A.R.Mujawar |
Abstract:In the developing country like India where farming being the backbone of the economy of the country and farmers being the effecting agents of the GDP, care has to be taken for the well being of them. On a case study it was been reviewed that a major portion of the investment for farming today is taken up by the weedicides and pesticides in order to control the grass in the crops. Hence to provide a alternate method for the removal of unwanted grass with a efficient monetary technique an idea of solar mulch cutter machine is brought forward in this paper.............
KEYWORDS - Solar Panel,Reel mover,DC Motor,Battery,
issue 11, April 2011
[2] Ashish Kumar chaudhari,Yuvrajsahu,Harshjain,IJARII-ISSN(O)-2395-4396 Experimental study of solar power grass cutter
robot ,vol-2,issue-2 2016
- Citation
- Abstract
- Reference
- Full PDF
Paper Type | : | Research Paper |
Title | : | Wall Painting Robot |
Country | : | India |
Authors | : | P.U.Gaikwad || Pavan Wankhede || Abhijit Daule || Rohit Wayse || Vishnwaghmare |
Abstract:Wall Painting robot is the machine which we can use for painting walls of the houses, offices, hospitals,etc.Wall painting robot is made just to overcome the conventional methods of painting, reduce human efforts involved in the whole painting process. It has a painting gun mounted on the the reciprocating arm of the robot, which is pneumatically operated. The gun has upside down reciprocating motion around the wall. After comlpetion of upside down motion cycle the robot moves across the wall through some calculated distance to paint the other patch of the wall.This motion is given to robot by means of chain sprocket mechanism,which is driven by a motor and the motor is controlled by using electronics circuit.As this system is easy in handling, it is applicable to various works for a wide range of structures without limiting work subjects.
Keywords - Wall Painting Robot, Structure
[1] Keita SUZUKI, Toshio SEKITO, Makoto HASEGAWA and Hiroshi KATOH, Learning by doing "Paper Bicycle Design an
Manufacturing", Proceedings of the 22th Design and Systems Division Conference, 1312, The Japan Society of
MechanicalEngineers, Hiroshima, Sept 26-28, 2012.
[2] Toshio SEKITO, Makoto HASEGAWA, Keiichi KUWAHARA and Hiroshi KATOH, A Challenge to grow up new system
engineers who have the sense for product engineering by the"Paper Bicycle Course", Proceedings of the 18th Design and
Systems Division Conference, 3403, The Japan Society of Mechanical Engineers, Kyoto, 2008.9.25-27.
[3] Thomas F, Ros L. Revisiting trilateration for robot localization. IEEE Transactions on robotics, 2005, 21: 93-99.
[4] Vedakkepat P, Miin O, Peng X, et al. Fuzzy behavior based control of mobile robots. IEEE Trans. fuzzy syst. 2004, 12: 559-567.
[5] Young S. Kim1, Myung H. Jung1, Yong K. Cho,"Conceptual design and feasibility analyses of robotic system for automated
exterior wall painting
- Citation
- Abstract
- Reference
- Full PDF
Paper Type | : | Research Paper |
Title | : | Quadcopter for Surveillance Application – A Review |
Country | : | India |
Authors | : | A.A. Bhujbal || P. P. Khedkar || Y. S. Agrawal || A. N. Dambalkar || Prof. S. B. Pawar |
Abstract:The Unmanned Aerial Vehicles (UAVs) has an ability to operate in dangerous locations while keeping their human operators at a safe distance. Due to which they have immense applications in the area of surveillance and emergency rescue. Quadcopter is a multi copter that is lifted and propelled by four rotors. In Quadcopters the lift is generated by a set of revolving narrow-chord airfoils. Quadcopters generally use symmetrically pitched blades for better stability. Control of vehicle motion is achieved by altering the pitch and/or rotation rate of one or more rotor discs, thereby changing its torque load and thrust/lift characteristics. It is controlled by radio transmission or operates under the guidance of limited autonomous protocols. This paper is a presentation of the design methodology and realization of the Quadcopter, a normal model aircraft based on a four-propeller design.
Keywords – UAV, Quadcopter, Rotor, Roll, Pitch, Thrust, Power, ESC
[1] Prof. Swati D Kale, Swati V Khandagale, Shweta S Gaikwad, Sayali S Narve, Purva V Gangal., Agricultural Drone for Spraying
Fertilizer and Pesticides, IJARCSSE, December 2015, Vol.5, Issue 12.
[2] Albin Boban, Ershad V N, Krishnakumar P, Preethi Sebastian, Solar Empowered Quad-Copter with Smartphone Control, IJAREEIE,
March 2016, Vol.5, Issue 3.
[3] Vinod Ingale, Umar Mulani, Quad Copter Controlling Using Android Mobile Devices, IJIRCCE, June 2015, Vol.3, Issue 6.
[4] Mohd Khan, Quadcopter Flight Dynamics, IJSTR, Vol.3, Issue 8.
[5] Mr. Kalpesh N. Shah, Mr. Bala J. Dutt, Hardik Modh, Quadrotor – An Unmanned Aerial Vehicle, IJEDR, Vol.2, Issue 1.
[6] Shilpa Kedari, Pramod Lohagaonkar, GangaramPalve, Prof. Pallavi Yevale, Real Time Wireless Communication between Quadcopter
and Android in Agriculture Field- A Review, IJARCSSE, Vol.5, Issue 11, November 2015.
- Citation
- Abstract
- Reference
- Full PDF
Paper Type | : | Research Paper |
Title | : | Special Purpose Machine for Linear Welding |
Country | : | India |
Authors | : | Prof.Shendage Yogesh.R || Maske Dikshant P || Kawachat Nivruti C |
Abstract:In today's edge of technology the demand of precision is increasing. The tradition methods are replaced by the automation to increase accuracy and precision increase the quality of welding, incorporation of the semi- automated welding machine is done for. certain application. For that different parameters and methods have tobe considered from different research paper for the welding machine for selection of mechanism like controller, welding process, weld angle etc. toget accuracy and quality weld. The technical constraint that has tobe considered while designing and developing the machine is to achieve the stability, degree of freedom, linear and angular motion, and uniform speed of the welding torch for feed and uniform thickness of weld for quality product..............
Keywords -SPM, Automatic welding, Design of Machine, Robotic Welding ,Machine Vision
[1] Gaurav Bhavsar Et.Al, "Design And Development Of Special Purpose Machine Used For Circular Metal Inert Gas Welding",3rd
International Conference On Scince,Technology And Management,Indian International Center,New Delhi,17Jan2016(ICSTM-16)978-
81-932074-0-6
[2] Dhage Kalyani P., Et.Al., , India Kalyanidhage8620@Gmail.Com , Chavanharshal@Gmail.Com, "Design And Manufacturing Of
Automatic Circular CO2 Welding Machine",International Engineering Research Journal Page No 203-207
[3] Virendrakumar Mahajan "STUDY OF DESIGN AND MANUFACTURING OF AUTOMATED TORCH ROTARY WELDING
MACHINE",International Conference On Emreging Trends In Engineering And Management Research
[4] 23rd March2016,(ICETEMR-16),ISBN:978-81-932074-7-5
- Citation
- Abstract
- Reference
- Full PDF
Paper Type | : | Review Paper |
Title | : | Limitations of Current Metallic Bone Plates: towards Development of Composite Bone Plates |
Country | : | India |
Authors | : | Sourabh Suresh Awati || Sanket Anil Borgave || Prof.Rajkumar.M.Deshmukh |
Abstract:Metals remaincomprehensively used in a erraticism of proposals in the medical field forinternal support and biological tissue exchanges, such as joint replacements, dental roots,orthopedicobsession, and stents.The metallic bone plates have certain complications like metal inappropriateness, corrosion, charisma effect, anode-cathode rejoinders, as well as a decrease in bone mass, increase in bone permeability. also,these plates, made of stainless steel or titanium alloys, tend to shield stress broadcast at the fracture site and interruption the bone healing degree. Therefore, composite materials for bone plates with progressive strength and stiffness and more semblance to natural bone had started to develop. This study examinesboundaries of metallic implants and the probability of acceptingprogressive composite materials to overawed stress shielding effectsto match more carefully to the bone.
Keywords - Bone plates, bone plate material, Stress shielding effect,Composite Material.
[1] Cornel IGNA, Larisa Schuszler, Current Concepts of Internal Plate Fixation of Fractures,Bulletin UASVM, Veterinary
Medicine 67(2)/2010 ISSN 1843-5270; Electronic ISSN 1843-5378
[2] R. M. Deshmukh†* and S. S. Kulkarni, A Review on Biomaterials in Orthopedic Bone Plate Application, International
Journal of Current Engineering and Technology E-ISSN 2277 – 4106, P-ISSN 2347 – 5161
[3] MitsuoNiinom, Mechanical biocompatibilities of titanium alloys for biomedical applications, journal of mechanical
behavior of biochemical material 1 ( 2 0 0 8 ) 3 0 – 4 2
[4] Abdulsalam A. Al-TammiePaulo, ChrisPeach, GlenCopper. Metallic bone Fixation implants: a novel design approach
for reducing the stress shielding phenomenon, virtual and physical prototyping ISSN:1745-275
[5] Hans K. Uhthoff1, Philippe Poitras2, and David S. Backman2, Internal plate fixation of fractures: short history and
recent developments,J OrthopSci (2006) 11:118–126DOI 10.1007/s00776-005-0984-7
- Citation
- Abstract
- Reference
- Full PDF
Paper Type | : | Research Paper |
Title | : | Failure Analysis For Initiation Of Crack On Helical Pinion Shaft- A Review |
Country | : | India |
Authors | : | Gadekar Rahul || M. A. Kumbhalkar || Gayakawad Akash || Jadhav Dhananjay || Phalake Ashitosh |
Abstract:WAG means Wide gauge AC traction Goods duty.WAG-9 is the most powerful engines in the country yet. For time to time service consideration in passenger as well as goods transport, the efficiency as well as longer service life of system components are important factors. The component which has been study is obtained from the "Central Railway Electric Locomotive Workshop, Bhusawal, India."In the recent study, the premature failure of traction motor assembly in WAG-9 is carefully investigated. The various literatures has been carefully compared and reviewed to get a proper helical pinion shaft failure analysis. From these literature reviews, the main objective of this paper is to study various Shaft Failure Analysis and Methodologies to select the best method to find out and analysis the Initiation of crack on Pinion Shaft.
Keywords - Failure analysis, crack detection, methodologies, traction assembly.
[1] "Central Railway Electric locomotive Workshop",Bhusawal.
[2] P.P. Nanekar and B.K. Shah "Characterization of Material properties by Ultrasonic‟s Atomic fuels division, Bhabha Atomic
Research Centre, 2003 p.25-38.
[3] Peterson R, Rice SL. Case Crushing of Carburized and Hardened Gears. SAE Technical Paper 610034; 1961.
[4] Gys van Zyl*, Abdulmohsin Al-Sahil, "failure analysis of conveyor pulley shaft", case Students in Engineering failure Analysis,
vol.1 pp.144-155, 2013.
- Citation
- Abstract
- Reference
- Full PDF
Paper Type | : | Research Paper |
Title | : | Study For Frequency Response Of Railway Vehicle Using Modal Analysis |
Country | : | India |
Authors | : | Vibhor Gujjewar || Vaibhav Jangid || Rohit Jagdale || Vaibhav Kadam || Prof. M.A. Kumbhalkar || Mr. P. P. Chaoji |
Abstract:Suspension System is an important element of rail road vehicle. It absorbs the shocks and vibrations during tracking, curving and also protect the axle movement. The helical compression type of spring is used to allow axial deformation. In this paper the investigation starts with the stress analysis with respect to the mechanical properties of material by analytical methods of Primary Suspension Springs at various tracking conditions. Further it is continued with the Modal Analysis of the Locomotive for the Vertical excitation.
Keywords - Helical Spring, PrimarySuspension System, Stress Analysis, Finite Element Analysis, Modal. Analysis, Vertical Excitation
[1] Failure Analysis Of Inner Suspension Spring Of. Manoj A. Kumbhalkar, Prof. Y. L. Yenarkar And Mr. A. K. Grover. Nagpur
(India) : AMAE, 2011.
[2] Static Analysis Of A Primary Suspension. K Pavan Kumar, S Praveen Kumar And G Guru Mahesh. S.L. : IJMERR, 2013.
[3] Material And Stress Analysis Of Railroad Vehicle Suspension. Manoj A. Kumbhalkara, Dr. D. V. Bhope, Dr. A. V. Vanalkar.
Nagpur : Elsevier, 2014.
[4] THE Generalized Coordinate Method For Discrete Systems. Irvine, Tom. 2004.
[5] Study On Bogie And Suspension System Of An Electric Locomotive (Wap-4). S. Naveen, C. P. Kiran, M. Prabhu Das, P. Naga
Dilip, V. V. Prathibha Bharathi. Hyderabad : International Journal Of Modern Engineering Research (IJMER).
- Citation
- Abstract
- Reference
- Full PDF
Paper Type | : | Research Paper |
Title | : | Comprehensive Review On Performance Combustion And Emission Of Diesel Engine Using Biofuel |
Country | : | India |
Authors | : | Prof. A. K. Nayse || Akshay S. Patne || Sanket S. Pol || Akshay J. Pavane || Somnath R. kore |
Abstract:For the past several years extensive efforts are being made to search for alternative fuels to overcome the dependence on fossil fuel and pollution. Direct injection diesel engines are more popular in the automotive sector than spark ignition (SI) engines due to its fuel lean operation. However, the use of fossil fuel is rising day by day and hence the major fuel source of petroleum-based fuel is depleting rapidly. Many countries depend mainly on imported fossil fuels due to lack of fuel reserves and it has the great impact on the economy. Several alternative fuels namely, hydrogen, oxygenated fuels like alcohol fuels, dimethyl ether and biodiesel fuels, etc., have been extensively analyzed. Recent studies show that biodiesel is one of the most promising alternative fuels for diesel engines because of its biodegradable, oxygenated and renewable characteristics............
[1] S. S. Ingle 1, V. M. Nandedkar2 (Dept. of Production Engg., SGGS Institute of Engineering & Technology, Nanded, India )
[2] K. B. Yogeshwaran1 ,G. Raghu2 ,G. Naveenraj3 1, 2, 3 (Assistant Professor, Department of Mechanical Engineering,
Adhiparasakthi Engineering College, Melmaruvathur. Tamilnadu,india)
[3] AmH.M. Mahmudula,⁎, F.Y. Hagosa, R. Mamata, A. Abdul Adama, W.F.W. Ishakb, R. Alenezic
[4] a Faculty of Mechanical Engineering, University Malaysia Pahang, 26600 Pekan, Pahang, Malaysia b Faculty of Industrial
Science & Technology, University Malaysia Pahang, 26600 Pekan, Pahang, Malaysia c Chemical Engineering Department,
College of Technological Studies, Public Authority for Applied Education and Training, Shuwaikh 70654,
[5] Rupesh J. Yadav†*, Prashant K. Kurve‡ and Pooja J. Pawarϯ †Department of Mechanical Engineering, MIT College of
Engineering, Pune-411038, India
- Citation
- Abstract
- Reference
- Full PDF
Paper Type | : | Research Paper |
Title | : | Design & Analysis for Intake System of Formula SAE Car |
Country | : | India |
Authors | : | Prashant A Dhaware || Chetan V sumbare || Chinmay S Sonawane || Abhishek Rasane || Mahesh Take |
Abstract:RSSCOER Pune University's, Team Supra 2.0 performed the study of intake restrictor design. The study was adotpted in order to improve engine performance by analyzing the inlet flow parameters and increase team's competitiveness at Formula SAE competitions. The most important objective of this project was to optimize the venture type of restrictor included in the intake system as imposed in the FSAE rule. Various intake designs like top/center feed intake, side entry intake, and conical spline intake designs were brought into influence. Implementation of CFD flow modeling software was achieved to analyze the fluid flow through the intake.The minimum pressure drop was achieved by careful observation of converging and diverging angles of 12 degree and 6 degree respectively.
intake system for a Formula SAE application.69th Conference of the Italian Thermal Machines Engineering Association"
2. Luca Romania, Giovanni Vichia, Alessandro Bianchinia, Lorenzo Ferrarib, Giovanni Ferrara"Optimization of the
Performance of a Formula SAE Engine by means of a Wastegate Valve Electronically Actuated"
3. Abhishek Raj, J.C. Mohanta, Bireswar Paul, Mohd. NayabZafar "design of a new improved intake manifold for f-sae car"
issn (print):2394-6202,(online):2394-6210,volume-2,issue-4,2016
4. BijuKuttan P, M Sajesh "Optimization of Divergent Angle of a Rocket Engine Nozzle Using Computational Fluid
Dynamics"The International Journal Of Engineering And ScienceIssn: 2319 – 1813 Isbn: 2319 – 1805
- Citation
- Abstract
- Reference
- Full PDF
Paper Type | : | Research Paper |
Title | : | Oscillating closed loop pulsating heat pipe: A Literature review |
Country | : | India |
Authors | : | Kishor S. Samudre || Omkar M. Pise || Vivekn.Lad || Akshay B. Pujari || Prashant B.Maitreya |
Abstract:The experimental results on the thermal performance of close loop pulsating heat pipe is represented by many researchers. The CLPHP is made of copper capillary tube, having inner tube and outer tube are 1.78mm and 3mm respectively. In this experiment we are going to study the effect of inclination angleand working fluid on heat transfer performance of CLPHP .The performance is done with inclination angle of 0 (vertical), 30,45,60,75,and 90 (horizontal).The working fluid used as methanol for experiment filling ratio [FR]50%, 11 turns of copper capillary tube. The length of evaporator,condenser,and adiabatic section are 50mm of each. Silver metal coating on copper capillary tube in evaporator and condenser section.
Keywords - Pulsating heat pipe; Oscillating heat pipe;Heat transfer performance; Thermal resistance
performance, Journal of Procedia Engineering 51(2013)624-629
[2] Dharmapal A. Baitule and Pramod R. Pachghare, Experimental analysis of closed loop pulsating heat pipe with variable
filling ratio, International Jounral of Mechanical Engineering and robotics Research,Vol.2,No.3,July 2013
[3] SuchanaAkter Jahan, Mohammad Ali, Md.Quamrul Islam, Effect of inclination angles on heat transfer characteristics of a
closed loop pulsating heat pipe(CLPHP), Procedia Engineering 56(2013)82-87
[4] Pramod R. Pachghare, Ashish M.Mahalle, Thermo-hydrodynamics of closed loop pulsating heat pipe: An experimental
study, Journal of Mechanical Science and Technology 28 (8) (2014) 3387~3394
[5] D. Manginia , M. Mameli a, * , A. Georgoulas a , L. Araneo c , S. Filippeschi b , M. Marengo, A pulsating heat pipe for
space applications: Ground and microgravity experiments, International Journal of Thermal Sciences 95 (2015) 53e63
- Citation
- Abstract
- Reference
- Full PDF
Paper Type | : | Research Paper |
Title | : | Design of Pipe Bending Machine |
Country | : | India |
Authors | : | Chetakraj Chavan || arjun Dhamale || Sharad Gaikwad || Gunjan Jawale || Prof. S. G. Chitnis |
Abstract:The objective of the subject is to make new design of manually and hydraulically operated pipe bending machine and stress acting on pipe after bending of pipe. The pipe bending machine is use to bend pipe in different angle shape and curvature as requirement of work. The machine is useful to bend different thickness pipe as per the requirement of shop. The machine is fully portable type and less weight and easy to assemble and disassemble. The can operate unskilled operator. Our main objective is useless parts for manufacturing pipe bending machine. And analysis different stress act on pipe using ANSYS Workbench.
Keywords - Steel pulley, Metal Frame, Bending pipe, lever, Model Analy
[2] V. B .Bhandari (2012) " Design of Machine Elements" Mc Graw Hill.
[3] Dhaval sutar (2015) "International journal of research in mechanical engineering and technology"
[4] Jun Zhano Gaocgao yu Rai Ma "Journal of Material Processing Technology"
[5] Chudasama (2014) Bending Force prediction for dynamic during 3-roller conical bending process. Journal of
manufacturing process.
- Citation
- Abstract
- Reference
- Full PDF
Paper Type | : | Research Paper |
Title | : | Design Of U-Drilling Fixture For Axle Arm |
Country | : | India |
Authors | : | Prof. S.S.Bhosale || Dattatray Karne || Sahilmaner || Akshay Salunkhe || Akshay Shelke |
Abstract:Productivity & quality are the major factor for growth of our indian manufacturing sector. The total machining time is reducing by improving the productivity. In various industries the verity of job is less and high quantity of job produced. Because of high productivity mass production occurs, this is possible when reducing total cost and saving time.so mass production isachivedby use of fixtures. In this project the design of U-drill fixture for drilling operation at different positions. Such fixture are made accurate and precise drilled hole and also individual positioning, marking, frequent checking are eliminated...............
Engineering, Nagpur, India) ; "Design of Angular Drilling Fixture and Analysis of Cutting Forces during Drilling on
Cylindrical" (J ApplMechEngg 2012)
[2] Satyajeetsinh Raijada1 AmitDudhatra [3] (P.G. Student 2Assistant Professor
[3] Department of Mechanical Engineering) " Design of a Fixture Connecting Rod forBoring
[4] operation(Vol 2 Issue 09, 2014)
[5] Midhun.R1Vignesh.( 1Assistant Professor 2UG Scholar)
- Citation
- Abstract
- Reference
- Full PDF
Paper Type | : | Research Paper |
Title | : | Abrasive Jet Gun |
Country | : | India |
Authors | : | Shital Bhosale || Praveen B Kothawal || Swapnil Adlinge || Nilesh Vishwekar || Ajit Waghmode |
Abstract:The AJM (Abrasive Jet Machining) Is A Non-Traditional Process, But Because Of The High Advantages Like, Machining Of Both Hard & Brittle Material, No Direct Contact Of Work Piece And Machine (Machining Obtained With Minimum Vibration), It Is Very Useful For Machining Operations . The Major Problem Of This Process Is The High Cost And The Bulky Size Of Machine. This Paper Is Presented For Reducing Machining Cost & Reducing The Size Of Machine.
Keywords - Compact Design, Elimination Of Some Parts, Glass Drilling, Deburring.
advanced engineering technology (E-ISSN 0976-3945) From Hyderabad India.
[2] Tarun Batra and Devil Journal paper- Literature Review On Abrasive Jet Maching from international journal of research in
aeronotical and mechanical engineering ISSN(ONLINE):2321-3051 VOL.3 ISSUE 12, DECEMBER 2015 , Pgs: 26-32.
[3] Hassan Mohamed abd EL hafez port said university Article: Drilling Of Glass Sheets By Abrasive Jet Machining, published on
19 january 2016.
[4] Tharoon T paper- Design And Fabrication Of Pneumatic Mirrior Holling Machine from International research journal of
engineering and technology (IRJET) e-ISSN:2395-0056, P-ISSN:2395-0072 VOLUME:033 ISSUE 12-DEC-2016.
[5] s. rajendra Prasad, dr.k.ravindranath, dr.m.l.s.devakumar paper-A Research Review On Advanced Approches In Abrasive Jet
Machining, IOSR Journal Of Mechanical And Civil Engineering(IOSR-JMCE), e-ISSN:2278-1684, p-ISSN:2320-334X, PP 57-
62.
- Citation
- Abstract
- Reference
- Full PDF
Paper Type | : | Research Paper |
Title | : | Modelling And Simulation Of Regenerative Braking System For Light Commercial Vehicle- A Review |
Country | : | India |
Authors | : | Shubham Shewate || M. A. Kumbhalkar || Yogesh Sonawane || Tushar Salunkhe || Samrat Savant |
Abstract:In this paper, Regenerative braking strategy for hybrid vehicles is studied. As the usage of fuel resources increasing day by day, the lack of fuel and environmental pollution become a serious problem. For such Problems, Hybrid Electric Vehicles are one of the better solutions. As we know that energy can neither be created nor be destroyed, it can be just converted from one form to another. Regenerative braking is one of the techniques adopted by HEVs in which, Kinetic energy is converted into electrical energy and use it directly or store in battery for further use. This Paper includes the study of HEVs and Regenerative braking system. Also, the study of modelling and simulation for regeneration model developed in modern simulation tools has been introduced.
Keywords - Hybrid Vehicles, Regenerative Braking Strategy, Simulation.
Vehicle
[2] SONIYA.K. MALODE, R.H.ADWARE, REGENERATIVE BRAKING SYSTEM IN ELECTRIC VEHICLES, International
Research Journal of Engineering and Technology (IRJET) Volume: 03 Issue: 03
[3] PULKIT GUPTA, ANCHAL KUMAR, SANDEEPAN DEB, 4SHAYAN, REGENERATIVE BRAKING SYSTEMS (RBS)
(FUTURE OF BRAKING SYSTEMS), International Journal of Mechanical and Production Engineering, Volume- 2, Issue- 5
[4] John William Miller, Design of a Single Axle Regenerative Brake System for a 2005 Thru-the-Road Hybrid Electric Chevrolet
Equinox, Master's Thesis, University of Tennessee, 2006.
[5] Brian Su-Ming Fan, Modeling and Simulation of a Hybrid Electric Vehicle Using MATLAB/Simulink and ADAMS, University
of Waterloo, Ontario, Canada, 2007
- Citation
- Abstract
- Reference
- Full PDF
Paper Type | : | Research Paper |
Title | : | A Review on - Experimental Investigation of Process Parameters in EDM Process |
Country | : | India |
Authors | : | Mahendra.U. Gaikwad || Sharad Dikule || Shubham There || Adesh Hande || Akshay Hatkar |
Abstract:Electrical discharge machining(EDM) is one of the nontraditional machining process based on thermo electric energy between the work piece and an electrode. In this process the material removal is occurred electro thermally by a series of successive discrete discharge between electrode and work piece. This paper presents a review of research work carried out for Aluminum material worked on Die sink EDM in Powder mixed EDM, EDM in water and Micro EDM..The input parameters consider are current, Pulse on time and Pulse off time whereas output parameters related to surface roughness, material removal rate, and tool wear rate.
Keywords - Material removal rate, Tool wear rate, Surface roughness
Inconel 718, 12th global congress on manufacturing and management, Procedia Engineering 97 ( 2014 ) 1512 – 1523.
[2] Avinash Choudhary, Mohan Kumar Pradhan ,Finite Element Analysis of Electro Discharge Machining using Ansys, Proceedings
of 1st International Conference on Mechanical Engineering: Emerging Trends for Sustainability,(2014) 18-26.
[3] AbhinandanA. Gosavi, Prof.A. B. Gaikwad, Predicting Optimized EDM Machining Parameter through Thermo Mechanical
Analysis, IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE), Volume 13, Issue 3 Ver. V (May- Jun. 2016), PP
71-85.
[4] Bai Shao, Kamlakar P. Rajurkar, Modelling of the crater formation in micro-EDM, 9th CIRP Conference on Intelligent
Computation in Manufacturing Engineering, Procedia CIRP 33 ( 2015 ) 376 – 381
- Citation
- Abstract
- Reference
- Full PDF
Paper Type | : | Research Paper |
Title | : | Analysis for Failure in Welding in Welding of Pivot Pin in WAP 4 Locomotive |
Country | : | India |
Authors | : | C. K. Chepparge || Adesh Borhade || Akash Gangad || Dnyaneshwar Gavakar || Akshay Bhosale |
Abstract:The project "Analysis for failure in welding of pivot pin in WAP 4 locomotive" contains weld failure of one part in locomotive that carries whole load of locomotive body. Analytical result and FEA result of static loading condition gives result of failure. Loading condition causes the failure of pivot pin weld. So, modification is essential to eliminate this failure. FEA analysis of weld gives stress values for existing pivot pin which can eliminate by proposed design of pin.
Keywords - FEA Analysis, Pivot pin, WAP 4.
System of an Electric Locomotive (Wap-4)" International Journal Of Modern Engineering Research (IJMER)..
2. Design data book ofkalaikathirachchagam.compiled by PSG College of Technology,Combtore.Reprinted in Sept-2013 Page
No.11.4, Design Stresses For Welded Joints.
3. A Textbook of Machine design by R.S. Khurami and J.K.Gupta of S.ChandPublications.reprinted 2010,Page no.354-Tabble
10.5:366- Eg No.10.10
4. M. A. Kumbhalakar, Dr. D. V. Vanalkaraetc (2014) Material and stress analysis of rail road suspension, PROCEDA Material
Science